Integrating the VIC-1 with other equipment

From RadioNerds
Jump to navigation Jump to search

Integration

Integrating the VIC 1 with other equipment is quite easy. There are some common connections that can be used. The biggest worry here will be to isolate the 12 volt radios from the 24 volt VIC-1, you can't simply hook these things together and expect them to not fry one another.

The biggest concern is when you are using a 24 to 12 volt converter in the vehicle and run the FM radio for example on 12 volt and the VIC-1 on 24, this could lead to damaging either one. If its an IPOD that isn't powered by the truck, (no cig plug, for example) then your likely ok.c


There are some common things that people want to do...
  1. Hook up an FM radio, Satellite receiver, scanner, ipod, or other MP3 player. RX (receive) ONLY
  2. Hook up a Transceiver, like a CB, FRS/GMRS radio, Ham Radios etc. This is TX (Transmit) / RX

Receive Only Inputs

Using the "Audio Input or "Tele / Remote" Inputs

You can make a simple pigtail from an old set of headphones and wire your ipod straight to these jacks.

Audio plug.png


Audio Input Jacks (left side)
These are amplified and will give you more input volume
Audio Ground (ring) connector to GND
Tip to the other
Tel/Remote jacks (right side)
These are 600ohm input sources for other military gear, these will be too low for use in most cases


Using the J508 Power Jack

To integrate something that is RX only, the best thing to do is to use the J508 4 pin power jack. Although this is a power input when the intercom is in Internal (no military radio hooked up) mode, this is NOT used when a MT-1029 is on the system. This is because the VIC1 will get its power from the radio mount on J501 or J503. This plug doubles as an RX input source.

To hook up an input source simply use this hookup

Vic1-4-pin-civilian-rx-cut.png

NOTES: - Need to verify the impedance of T-1 to insure proper matching, this is really here for unity and to maintain isolation


To use the circuit above you simply need to provide audio to the audio inputs from a line-out source on the radio. Line out is desired because it is usually quite low, and a fixed level, you want the Vic1 to do the amplification. You could use a speaker out, but you need to be very careful not to give it too much volume, the VIC1 wont react well, it will clip (sound distorted) and overdrive the amp. I do use the same circuit above to plug in my ipod and it works perfectly as long as the volume is reasonable. You wont smoke it as along as your not attempting to slam 300 watts from an amp into it.

How Can I use the Power Plug for Audio, if im using it for Power?

Well thats a good point. The Vic-1 has the ability to get its power from the MT-1029 mount. Even if you aren't putting in a radio you can still use this configuration to free up the power port. You are essentially using the power block as a power point. and if you have other 24volt accessories, you can plug in to the other power ports on the block.

  • 1) Remove the power block from an MT-1029 mount.. to do this remove the phillips head screws from around the block. unscrew the collars on the connectors. the block should come off.
  • 2) Remove the Power cable from the VIC-1 (J508) and plug into the power block
  • 3) Connected the VIC-1 radio "A" (J501) cable to the block
  • 4) Move the "Installation Switch" on the VIC-1 to "OTHER"

You will now power the VIC-1 via the Radio "A" (J501) cable instead of the power plug (J508)

Transmit and Receive inputs

This is a much harder situation, as i stated before you cant simply start splicing things together to get this going, you will certainly smoke a radio. You need to isolate the audio in and out and the PTT key circuits from each other. fortunately there is a fairly straightforward method to do this.

Rib1-basic.png



SEE AM-1780 for Jack details

TX / RX
J501 or J503 must be used, they use the CX-4723 - 18 Pin Cable.


RX only
J508 or J510


Images


Example of My integration

These are some photos of my integration of the VIC1 with civilian radios, i used the circuit defined in

Updated Circuit Boards / Designs

I have created a Circuit board that will make this much cleaner and neater. This board is designed to be used alone with a single radio, or grouped together by means of a link board. the point here is that you can have up to 4 radio in one system, and be able to choose which radio will be keyed when you activate the PTT on the VIC1. In a certain configuration, you can key ALL THE RADIOS at once! now thats fun!

How it Works

these are designed to allow you to use only one board or multiples into one intercom system. For example, you could use a single RIB to hook up a single cb and run that for awhile, then decide to add some other radio like GMRS or ham. all you need to do is to make an additional rib, add the link board and it's all ready. if something goes wrong with any rib or link board, you can always swap them out to any radio and it will work again. Also the design allows the radio to continue working via the regular mic, because I integrated the pigtail into the radion, and not the mic jack. If the whole thing blows up, the radio is still the same functional one you had when you started.

Examples

(better graphics later)

Single radio

Radio ---> RIB ---> AM-1780


Multiple radios

Radio ---> L

Radio ---> I ---> AM-1780

Radio ---> N

Radio ---> K

RIB Layout

Here is an early layout of the board.

V1A-rib-layout.png

this board is about 2in wide by 3 inches long..


Radio board.JPG

A few Design Details
  • 12v Sense - This allows the Remote PTT selector to indicate if the radio is plugged into the link board port, not needed if its used in a single radio configuration
  • PTT Cutoff / Enable - this allows you to disable PTT for this radio completely, this is good if you want an RX only radio, with no chance to transmit on it.
  • PTT indicator - this will light up when the radio is keyed
  • Receive resistor bypass - in some cases the resistor is needed to prevent overloading the input, like when you use a speaker out from the radio, use this jumper if your using a lower volume output from the radio
  • Bue pots - control the receive the transmit audio levels.

Link Board

Link board schematic.png


Link board.JPG


The link board allows you to run up to 4 radios into one vic. This one pictured does not have the PTT control port connector yet, that will allow you to select by a remote selector which radio will be keyed when you PTT from the vic. If you decide not to use the remote, you have to select the PTT radio manually by the small DIP switch. This would be done in advance. I know not very practical on the road, but thats why it has a remote selector. As an added bonus, you can actually allow it to key more than one radio at a time, by turning the PTT for multiple radios on. think of it! key all 4 radios at once!! sweet! (why you would want to is anyones guess, but hey, its still cool!)


Link board-radio board.JPG