Difference between revisions of "AN~GRR-5"

From RadioNerds
Jump to navigation Jump to search
 
(36 intermediate revisions by the same user not shown)
Line 1: Line 1:
:[[File:an_grr-5-5.jpg | 400px | AN/GRR-5]]
+
[[File:an_grr-5-5.jpg|400px|right]]
 
 
 
 
 
==Images==
 
==Images==
<gallery widths=100px heights=100px perrow=5>
+
<gallery widths=100px heights=100px>
 
File:an_grr-5-1.png
 
File:an_grr-5-1.png
 
File:an_grr-5-2.png
 
File:an_grr-5-2.png
Line 11: Line 9:
 
File:an_grr-5-7.jpg
 
File:an_grr-5-7.jpg
 
File:an_grr-5-8.jpg
 
File:an_grr-5-8.jpg
 +
File:An grr-5 CR102 schematic.jpg
 
</gallery>
 
</gallery>
 
  
 
==Power Hookups==
 
==Power Hookups==
Line 32: Line 30:
  
 
==Recommended Modifications==
 
==Recommended Modifications==
The AN/GRR-5 is an excellent radio, however during the time of its manufacture, some safety features we come to expect were not implemented.  The following items are recommended enhancements that will make the device safer to use with modern electrical systems.  All of these recommended procedures are fully reversable should you wish to return the radio to its factory condition.
 
  
 +
{{Template:NeedsUpdating}}
  
 
===Add a Grounded Power Cable===
 
===Add a Grounded Power Cable===
Line 45: Line 43:
  
 
===Replace Defunct Selenium Rectifiers with modern components===
 
===Replace Defunct Selenium Rectifiers with modern components===
There are a couple key components that are often defunct that can be replaced with modern equivalents.  Rectifiers and Diodes of the time used Selenium.  This material easily degrades and is often the cause of a non-working radio.  If they are not working they should be replaced with modern components.  Modern components are often not a direct replacement.  Selenium components often had a high resistance, the voltage that the downline components had was often designed with this in mind.  The resistance in modern components is minimal, and it may be necessary to install resistors to simulate the same characteristics as the old ones.
+
There are a couple key components that are often defunct that can be replaced with modern equivalents.  Rectifiers and Diodes of the time used Selenium.  This material easily degrades and is often the cause of a non-working radio.  If they are not working they should be replaced with modern components.  Modern components are often not a direct replacement.  Selenium components often had high resistance, the voltage that the downline components saw was often designed with this in mind.  The resistance in modern components is minimal, and it may be necessary to install resistors to simulate the same characteristics as the old ones.
 +
 
 +
 
 +
====Replace the Selenium Bridge Rectifier with a modern equivalent====
 +
My rectifier was blown, but i generally will look carefully at replacing these any chance i get, even NOS parts are usually no good.  Just replace with a modern one.
 +
 
 +
<gallery widths=400px heights=200px perrow=2>
 +
File:an_grr-5_factory_supply.png|'''Factory Power Supply (Red arrow shows selenium rectifier)'''
 +
File:an_grr-5_CR101_schematic.png|'''Detail of CR101 Selenium Rectifier'''
 +
</gallery>
 +
 
 +
====Relocate and replace the In case diodes with modern ones inside the power supply====
 +
This was originally required because the pins on the power cable connecting the power supply to the receiver were broken, but it also served as a nice way to get rid of the selenium diodes inside the case.  I removed the need for the case diodes, by replacing them with modern equivalents inside the power supply itself.
  
'''Power Supply'''
+
<gallery widths=400px heights=200px perrow=2>
<gallery widths=400px heights=250px perrow=5>
+
File:an_grr-5_selenium_rectifiers_in_cabinet.jpg|'''Selenium Diodes in Cabinet'''
File:an_grr-5_factory_supply.png|Factory Power Supply (Red arrow shows selenium rectifier)
+
File:an_grr-5_CR102_schematic.png|'''Detail of CR102 Rectifier in Cabinet'''
File:an_grr-5_modified_power_supply.png|Modified Power Supply
 
 
</gallery>
 
</gallery>
  
==Additional Files==
+
====Modified Power Supply with Both Changes====
 +
 
 +
[[File:an_grr-5_modified_power_supply.png|400px|'''Modified Power Supply''']]
 +
 
 +
 
 +
 
 +
==Interconnection Cable Pinout==
 +
 
 +
;J101
 +
:'''Pin 1''' + 24 V DC
 +
:'''Pin 2''' Diode in Case
 +
:'''Pin 3'''
 +
:'''Pin 4''' Diode in Case
 +
:'''Pin 5''' Ground
 +
:'''Pin 6''' +90 V DC
 +
:'''Pin 7''' +12 V DC
 +
:'''Pin 8''' - 4.2 V DC
 +
:'''Pin 9'''
 +
:'''Pin 10''' Ground
 +
:'''Pin 11''' +1.4 V DC
 +
 
 +
==Reference Files==
 
;{{pdf|TM_11-295.pdf‎|TM 11-295}}
 
;{{pdf|TM_11-295.pdf‎|TM 11-295}}
 
:Radio Receiving Set
 
:Radio Receiving Set

Latest revision as of 13:51, 29 June 2016

An grr-5-5.jpg

Images

Power Hookups

The AN/GRR-5 Radio has an exceptionally flexible power input specification. This radio can operate on 6, 12, or 24 Volts DC as well as 115 Volts AC. The voltage is determined by a switch on the front of the power supply or automatically in the case of 115 Volts AC.

hookups for each power range is made by different pins on the J103 Power plug. They are as follows:

6, 12, 24 Volts DC
Pin C - Ground
Pin B - 6, 12, 24 Volts DC
115 Volts AC
Pin D - AC
Pin A - AC
Idea.png
Grounding and Shock Hazards when in AC Power Mode
The AN/GRR-5 and similar era radios have a tendency to have voltage on the radio case when powered by AC sources. This is due to the lack of a ground lug on the factory power cord, and filter capacitors inside the radio that are connected to the radio case. This voltage can cause an uncomfortable shock, although its usually not fatal. Solutions can be found below in "Recommended Modifications" to remedy this.


Recommended Modifications

Incomplete.png
INCOMPLETE SECTION OR ARTICLE
This section/article is incomplete and requires more updates and work. Would you like to assist in this? request an account to help!

Add a Grounded Power Cable

Replace the factory 2 conductor plug and cord with a modern 3 prong grounded plug. To do this, unsolder the factory plug from the power cord and replace it with a modern, 3 plug type. Use the following pinout for hookups:

115 Volts AC
Pin A - AC
Pin C - Ground
Pin D - AC


Replace Defunct Selenium Rectifiers with modern components

There are a couple key components that are often defunct that can be replaced with modern equivalents. Rectifiers and Diodes of the time used Selenium. This material easily degrades and is often the cause of a non-working radio. If they are not working they should be replaced with modern components. Modern components are often not a direct replacement. Selenium components often had high resistance, the voltage that the downline components saw was often designed with this in mind. The resistance in modern components is minimal, and it may be necessary to install resistors to simulate the same characteristics as the old ones.


Replace the Selenium Bridge Rectifier with a modern equivalent

My rectifier was blown, but i generally will look carefully at replacing these any chance i get, even NOS parts are usually no good. Just replace with a modern one.

Relocate and replace the In case diodes with modern ones inside the power supply

This was originally required because the pins on the power cable connecting the power supply to the receiver were broken, but it also served as a nice way to get rid of the selenium diodes inside the case. I removed the need for the case diodes, by replacing them with modern equivalents inside the power supply itself.

Modified Power Supply with Both Changes

Modified Power Supply


Interconnection Cable Pinout

J101
Pin 1 + 24 V DC
Pin 2 Diode in Case
Pin 3
Pin 4 Diode in Case
Pin 5 Ground
Pin 6 +90 V DC
Pin 7 +12 V DC
Pin 8 - 4.2 V DC
Pin 9
Pin 10 Ground
Pin 11 +1.4 V DC

Reference Files

Adobe PDF icon.png TM 11-295

Radio Receiving Set
AN/GRR-5
August 1952