Difference between revisions of "Integrating the VIC-1 with other equipment"

From RadioNerds
Jump to navigation Jump to search
Line 14: Line 14:
 
=Port Overview=
 
=Port Overview=
  
[[File:AM-1780-1.png]]
+
[[File:AM-1780-1.png]
 +
 
 +
J501
 +
:"A" Radio connection. Also supplies power to AM-1780 in "OTHER" mode.
 +
 
 +
 
 +
;J503
 +
:"C" radio connection
 +
 
 +
;J504
 +
:Commander Control Box, Independent of Crew connections (J505-J507)
 +
 
 +
;J505
 +
:Crew Intercom Control Box, Paralleled with other crew jacks (J505, J506, J507)
 +
 
 +
;J506
 +
:Crew Intercom Control Box, Paralleled with other crew jacks (J505, J506, J507)
 +
 
 +
;J507
 +
:Crew Intercom Control Box, Paralleled with other crew jacks (J505, J506, J507)
 +
 
 +
;J508
 +
:Power connection when in "INT ONLY" mode or C RX radio in "OTHER" mode
 +
 
 +
;J509
 +
:[[C-2299]] Retransmission connection
  
 
= Receive Only Inputs =  
 
= Receive Only Inputs =  

Revision as of 03:13, 8 November 2011

Integration

Integrating the VIC 1 with other equipment is quite easy really.. there are some common connections that can be used. the biggest worry here will be to isolate the 12 volt radios and the 24 volt vic1, you cant simply hook these things together and expect them to not fry one another.


NOTE: One very important thing to note is that the VIC1 is 24 Volt and most Civilian radios are 12 Volt, you need to isolate them from each other if they are on connected to the system.


There are some common things that people want to do...
  1. Hook up a FM radio, Satellite receiver, scanner, ipod, or other MP3 player. RX (receive) ONLY
  2. Hook up a Transceiver, like a CB, FRS/GMRS radio, Ham Radios etc. This is TX (Transmit) / RX


Port Overview

[[File:AM-1780-1.png]

J501

"A" Radio connection. Also supplies power to AM-1780 in "OTHER" mode.


J503
"C" radio connection
J504
Commander Control Box, Independent of Crew connections (J505-J507)
J505
Crew Intercom Control Box, Paralleled with other crew jacks (J505, J506, J507)
J506
Crew Intercom Control Box, Paralleled with other crew jacks (J505, J506, J507)
J507
Crew Intercom Control Box, Paralleled with other crew jacks (J505, J506, J507)
J508
Power connection when in "INT ONLY" mode or C RX radio in "OTHER" mode
J509
C-2299 Retransmission connection

Receive Only Inputs

Using the "Audio Input or "Tele / Remote" Inputs

You can make a simple pigtail from an old set of headphones and wire your ipod straight to these jacks.

Audio plug.png


Audio Input Jacks (left side)
These are amplified and will give you more input volume
Audio Ground (ring) connector to GND
Tip to the other
Tel/Remote jacks (right side)
These are 600ohm input sources for other military gear, these will be too low for use in most cases


Using the J508 Power Jack

To integrate something that is RX only, the best thing to do is to use the J508 4 pin power jack. Although this is a power input when the intercom is in Internal (no military radio hooked up) mode, this is NOT used when a MT-1029 is on the system. This is because the VIC1 will get its power from the radio mount on J501 or J503. This plug doubles as an RX input source.

To hook up an input source simply use this hookup

Vic1-4-pin-civilian-rx-cut.png

NOTES: - Need to verify the impedance of T-1 to insure proper matching, this is really here for unity and to maintain isolation


To use the circuit above you simply need to provide audio to the audio inputs from a line-out source on the radio. Line out is desired because it is usually quite low, and a fixed level, you want the Vic1 to do the amplification. You could use a speaker out, but you need to be very careful not to give it too much volume, the VIC1 wont react well, it will clip (sound distorted) and overdrive the amp. I do use the same circuit above to plug in my ipod and it works perfectly as long as the volume is reasonable. You wont smoke it as along as your not attempting to slam 300 watts from an amp into it.


Transmit and Receive inputs

This is a much harder situation, as i stated before you cant simply start splicing things together to get this going, you will certainly smoke a radio. You need to isolate the audio in and out and the PTT key circuits from each other. fortunately there is a fairly straightforward method to do this.

Rib1-basic.png



SEE AM-1780 for Jack details

TX / RX
J501 or J503 must be used, they use the CX-4723 - 18 Pin Cable.


RX only
J508 or J510


Common integration Diagrams
Proper Isolated Interface for 12volt radios to Intercom with TX and RX
Civilian Radio Connections to A (J501) or C (J503)
Civilian Radio Connection to C-RX (J508)
Nokia Style headset Connection to A (J501) or C (J503)
Kenwood HT Connections to A (J501) or C (J503)


Example of My integration
These are some photos of my integration of the VIC1 with civilian radios, i used the circuit defined in Properly Hook Civilian Radio to VIC1
ProtoType circuit and additional wiring.
This uses the 18 Pin "C" Radio integration for full transmit and receive support. the DB9 plug is so that i can easily hook to many different radios that i have put a "pigtail" DB9 in.

IMG 0280.JPG


This is one of the radios. In this case its a EF Johnson, business band radio, programmed with the GMRS/FRS frequency set.

IMG 0281.JPG